
Throughout our Understanding IBCs series, we’ve explored the key considerations for filling, storing, transporting and emptying Intermediate Bulk Containers. Following our previous article on Ex-zone applications, let’s now look at specialist configurations for processes that require mixing, inliners or additional containment.
Choosing an IBC involves more than identifying the right capacity. The characteristics of the filling product, the equipment used and the requirements of your manufacturing process all influence the specification.
Here, we explain three options within the SCHÜTZ range and the practical considerations for their use.
Stirring Directly in the IBC
Some filling products require stirring before use. For these applications, an integrated stirring system enables mixing to take place directly inside the container.
The SCHÜTZ IMPELLER is a one-way stirrer attached to the screw cap and installed directly into the IBC by SCHÜTZ. A compatible stirring drive connects through an adapted steel shaft, which fits into the impeller’s hollow shaft.
An important feature of this arrangement is that the steel drive shaft does not come into contact with the filling product. After stirring, the shaft can be removed and reused, while the integrated stirrer remains with the IBC.
Both traverse and static stirring drives can be connected using the appropriate adapted shaft. Compatibility with your equipment should be confirmed before use.
Mixing Speed and Product Viscosity
Effective stirring does not necessarily require high rotational speeds. Depending on the product, the SCHÜTZ IMPELLER’s bucket agitator can achieve effective mixing at between 80 and 200 revolutions per minute.
Low-speed operation enables stirring without drawing in air or forming foam, allowing direct use of the filling product where appropriate.
When assessing an integrated stirring system, consider:
- The filling product: The appropriate mixing conditions depend on the product being handled.
- Viscosity: Products with viscosities of 5,000 mPa·s can be stirred, with higher viscosities subject to individual testing.
- Drive compatibility: The stirring drive and connecting shaft must be suitable for the system.
- Operating instructions: Follow the dedicated instructions for the integrated impeller.
The speed range should therefore be considered alongside the product’s characteristics, rather than treated as a single setting suitable for every application.
Filling IBCs with an Integrated Inliner
An integrated inliner provides another specialist IBC configuration, with its own filling arrangements and handling instructions.
Filling can generally take place through either of two routes:
- Through the top filling opening, using the inliner’s filling hose.
- Through the discharge valve at the bottom of the IBC.
The appropriate route depends on your filling arrangement and the instructions for the particular inliner system. Before starting, confirm which connection will be used and ensure the team follows the correct procedure.
Although these routes offer flexibility, the filling process should always be planned around the installed configuration. Instructions for a standard IBC should not automatically be assumed to cover an IBC fitted with an inliner.
Inliners for Food Applications
For food applications, the inliner connections can be treated with steam to reduce germs. Temperature and exposure time must be carefully controlled, particularly when treating the discharge valve.
The following maximum treatment times must not be exceeded:
| Steam temperature | Maximum treatment time | Approximate steam pressure |
| 120°C | 30 minutes | 1 bar |
| 125°C | 4 minutes | 1.4 bar |
| 130°C | 1 minute 45 seconds | 1.75 bar |
As the temperature increases, the maximum permitted exposure time reduces considerably. For example, the limit falls from 30 minutes at 120°C to just 1 minute 45 seconds at 130°C.
These figures are maximum exposure limits for the specified discharge-valve treatment, rather than a complete hygiene programme. Always follow the dedicated SCHÜTZ inliner instructions alongside your site’s food hygiene procedures.
After filling through the discharge valve, it is also recommended that a disinfectant is applied to the valve opening, either by spraying or using a soaked sponge.
Additional Protection with the ECOBULK SX-D
Where additional containment is required, the construction of the IBC is another important consideration.
The SCHÜTZ ECOBULK SX-D is a 1,000-litre IBC featuring:
- A closed steel outer hull.
- Double-wall construction for additional protection.
- Three top openings protected by steel caps.
When considering this configuration, assess the filling product and the conditions in which the container will be used. Capacity and construction are relevant, but suitability must be confirmed for the intended application.

IBC Expertise
Specialist IBC configurations should be selected with the full process in mind. Does your product require stirring before use? Will filling take place through the top opening or discharge valve? Are there specific hygiene or containment requirements?
Establishing these details helps identify the appropriate container, connections and operating procedures.
At Industrial Packaging, our experienced team can help you assess your requirements and identify a suitable IBC solution for your product and process.
Contact our team to discuss your application, or explore the previous articles in our Understanding IBCs series.
